One time I was called to a four unit business complex.  One of the businesses in the complex was a silk screening company.  They wanted to know what it would cost to put in air conditioning.

I scoped out the electrical service very carefully.  The electrical service to the building was right to the very limit of what it could take.  I notified the lady running the silk screening business that it would be quite expensive to install air conditioning in any one unit.

She would have to call the head office back east to get permission to spend the money for air conditioning.

When she got back to me with their response, it was; “In Washington it rains all the time, so air conditioning is unnecessary.”  (The head office experience in Washington must have been limited to the Seattle area.)  Their response kyboshed the whole job.

Sometime afterward, the National Electrical Code (NEC) came out with a ruling that you could have both heating and A/C considered as the same service load, as long as both weren’t operating at the same time.

If I had been smart enough at the time I could have figured that out!

I often think we didn’t have A/C in cars in my younger years.

Before electricity was brought to the farm we didn’t have A/C anywhere.

How did we ever survive?

I was sent to wire a theater being built on the South Hill.  I ordered a bunch of ½ inch and ¾ inch EMT conduit and stocked it on the job site.  Before the cement floor was poured, I laid a lot of conduit where the floor slab would be poured, and brought the conduits up into the area where the walls would be built.

While the cement was being poured and finished, I went to work on other jobs.  Sometime later I learned that another electrician had been sent to finish the theater job.  Later still, I asked the estimator how the theater job was going.  The estimator said that the electrician kept running out of ½” conduit.  I was not the boss, but I was still somewhat disappointed.

After more time had passed I was sent back to the theater job to complete it.  The other journeyman had run parallel ½” conduit runs, each containing only one circuit, the entire length of the building.  My original plan had been to run 2, 3, or even 4 circuits in each ¾” conduit.  The upshot was that the ½” conduit was way over budget and there was a lot of unused ¾” conduit left on the job.  It had been a very wasteful use of material.

I believe that this man was the same journeyman that, on another job, had been sent into the basement to install a three phase motor starter switch.  We sent three fuses with him.  The fuses we sent with him were of the proper size for the job he needed to do.

Later on he came back out of the basement saying he needed more fuses.  Then later he came back for more fuses.  Finally I went to see what was going on.  He had wires sticking out everywhere from the switch and a big pile of fuses on the floor.

I determined that he didn’t know what he was doing.  He had apparently hooked it up one way, had blown a fuse, taken all the fuses out, hooked up the starter switch with the three new fuses and tried it again.  And again.

He was sent somewhere else and I cleaned up the mess.  I soned all the fuses to find out that approximately 2/3 of them were still good.  I think about this time he was laid off.  How he ever got his journeyman card I’ll never know!

Once more I was sent to a bank to work on a Banking On Line installation.  On this particular job I needed to drill a hole through a concrete wall from a hallway into a room with a plethora of file cabinets.

We didn’t want to move all the file cabinets, and the drill we were using required water cooling.  The hallway did not have sufficient room to set up the drill, so we covered the cabinets with visqueen and set up a hose with running water to cool the bit.

I was told that the wall was filled with rebar made of steel, not iron.  Whereas we would have been able to cut through iron, the steel rebar would perhaps ruin the bit.  I got a blueprint of where the rebar had been placed in the wall.  There was no reference point inside the room with the file cabinets to determine where the rebar was.  It was necessary to determine the location from the hallway area.

In the hallway I carefully measured to an exact point where the rebar was located and marked an “X” in a location as the place I wanted to be sure to miss.  I then calculated the distance from that spot to the floor, measured 30 feet along the floor (a sloping floor), then I turned and measured down two steps and 8 feet laterally, then I turned again and measured up a step and into the file cabinet room 20 feet, then I turned and measured behind the file cabinets, and finally I measured back up the wall and put a dot on the wall where we would be drilling.

The “we” in this instance was a young apprentice that was helping me do all the measuring and marking and would be assisting in the drilling procedure.  I could tell he was doubtful that this method was going to work.  I didn’t tell him, but I was also doubtful.

We got on top of the file cabinets.  One of us would handle the water hose and the bucket to catch the water.  We took turns handling the drill and hose and bucket.  The drill bit was actually a hole-saw that cut a core out of the cement.  We would drill a while, pull the drill out and break out a piece of the core and drill again.  When we finally broke through we pulled out the drill and the last of the core.  There, right in the center of the core was the “X” I had made on the hallway wall.  The spot I had intended to miss.

I said to my apprentice, jokingly, “See how close we measured?”  We cleaned up our mess and I looked in the hole.  We had just skimmed the edge of one of the rebars.

The apprentice was called to another job our company was doing downtown and I finished up at the bank.  Then I was also sent to the same job he had been sent to.  The guys on that job said the apprentice had told them of measuring down the hallway across the room and up the wall and hitting the spot right on the mark.

I tried to explain to the other guys that it was the spot I had intended to miss.  Somehow they wouldn’t believe me.  I guess I had built up a reputation by that time.